Mechanical properties and corrosion behavior of Ti6Al4V particles obtained by implantoplasty: an in vitro study. Part II
Autor/a
Toledano-Serrabona, Jorge
Sánchez-Garcés, M. Angeles
Gay Escoda, Cosme
Valmaseda-Castellon, Eduard
Camps Font, Octavi
Verdeguer, Pablo
Gil Mur, Francisco Javier
Fecha de publicación
2021ISSN
1996-1944
Resumen
In the field of implant dentistry there are several mechanisms by which metal particles can be released into the peri-implant tissues, such as implant insertion, corrosion, wear, or surface decontamination techniques. The aim of this study was to evaluate the corrosion behavior of Ti6Al4V particles released during implantoplasty of dental implants treated due to periimplantitis. A standardized protocol was used to obtain metal particles produced during polishing the surface of Ti6Al4V dental implants. Physicochemical and biological characterization of the particles were described in Part I, while the mechanical properties and corrosion behavior have been studied in this study. Mechanical properties were determined by means of nanoindentation and X-ray diffraction. Corrosion resistance was evaluated by electrochemical testing in an artificial saliva medium. Corrosion parameters such as critical current density (icr), corrosion potential (ECORR), and passive current density (iCORR) have been determined. The samples for electrochemical behavior were discs of Ti6Al4V as-received and discs with the same mechanical properties and internal stresses than the particles from implantoplasty. The discs were cold-worked at 12.5% in order to achieve the same properties (hardness, strength, plastic strain, and residual stresses). The implantoplasty particles showed a higher hardness, strength, elastic modulus, and lower strain to fracture and a compressive residual stress. Resistance to corrosion of the implantoplasty particles decreased, and surface pitting was observed. This fact is due to the increase of the residual stress on the surfaces which favor the electrochemical reactions. The values of corrosion potential can be achieved in normal conditions and produce corroded debris which could be cytotoxic and cause tattooing in the soft tissues.
Tipo de documento
Artículo
Versión del documento
Versión publicada
Lengua
English
Materias (CDU)
616.3 - Patología del aparato digestivo. Odontología
Palabras clave
Implantoplàstia
Corrosió
Ti6Al4V
Implant dental
Implantoplastia
Corrosión
Ti6Al4V
Implante dental
Implantoplasty
Corrosion
Ti6Al4V
Dental implant
Páginas
13
Publicado por
MDPI
Colección
14;
Publicado en
MDPI
Citación
Toledano-Serrabona, Jorge; Sánchez-Garcés, Maria Ángeles; Gay-Escoda, Cosme [et al.]. Mechanical properties and corrosion behavior of Ti6Al4V particles obtained by implantoplasty: an in vitro study. Part II. Materials, 2021, 14(21), 6519. Disponible en: <https://www.mdpi.com/1996-1944/14/21/6519>. Fecha de acceso: 21 nov. 2021. DOI: 10.3390/ma14216519
Número del acuerdo de la subvención
info:eu-repo/grantAgreement/MICINN/RTI2018-098075-B-C21
info:eu-repo/grantAgreement/MICINN/RTI2018-098075-BC22
Este ítem aparece en la(s) siguiente(s) colección(ones)
- Odontologia [245]
Derechos
This is an open access article distributed under the Creative Commons Attribution License which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Excepto si se señala otra cosa, la licencia del ítem se describe como https://creativecommons.org/licenses/by/4.0/